Split EMC cable gland

for shielding cables with connectors, thread size M32/M63, IP55 The split cable gland EMC-KVT-DS is based on the standard icotek KVT product. However, the EMC-KVT-DS has been metallised (galvanise coated) to create a conductive surface. The first cable grommet (KT) is used for strain relief and cable sealing on the cable jacket. The second grommet (EMC-KT) contacts the cable shield at a full 360 degrees. The conductive flat gasket included in the scope of delivery makes contact between the cable gland and the conductive housing wall. The EMC-KVT-DS can thus be fixed using a plastic lock nut. Alternatively, an additional contact to the metal wall can be made using a special EMC lock…

Continue ReadingSplit EMC cable gland

KEL-DP multi-membrane cable entry plates

KEL-DP entry plates are designed for routing cables without connectors, hoses or fibre optics in limited space.  The KEL-DP products are an easy to assemble and cost saving alternative to traditional cable glands. Simply make a small hole in the thin membrane and push the cables through. The KEL-DP provides protection IP64 / UL type 12. The KEL-DP matches exactly the cut-out dimensions of 6-, 10-, 16- and 24-pin standard industrial connectors. The very compact size KEL-DP-E is designed for routing cables in very small space. Through a cut-out of only 18 × 112 mm, up to 21 cables can be easily routed and sealed. A special rib ensures a centred fit in the…

Continue ReadingKEL-DP multi-membrane cable entry plates

QVT split cable gland

for cables with connectors, M16 - M50 / IP54 QVT is a circular split frame for quick and easy installation of pre-terminated cables or complete cable harnesses. But also electric, pneumatic or hydraulic lines without terminals or connectors as well as corrugated conduits can be easily routed and sealed with IP54. Because of its extremely compact design, the QVT range is especially suitable for small machines, devices and instruments. The grommets of the QT series are used. The cable glands are easy to install. The prefabricated cable is placed into the slit grommet which is set into one of the gland halves. Depending on the size of the cable gland, one, two or…

Continue ReadingQVT split cable gland

EMC shield clamps for 35 mm top hat DIN rail, pluggable

with or without integrated strain relief EMC shield clamps are used, where the shield of cables must be connected to the earth potential. They are easy to use and effective in earthing single cable shields. When using types with integrated strain relief cables can be fixed via the cable jacket using cable ties. Thus strain relief in accordance with EN 62444 is achieved. We also offer EMC shield clamps with double strain relief function acc. to PROFINET installation guidelines. Due to its special design the clamping ranges of the MSKL are very large while the dimensions are comparatively small. (Example: MSKL 3-12, assembled with a 12 mm cable shield: width 26.25 mm). The…

Continue ReadingEMC shield clamps for 35 mm top hat DIN rail, pluggable

KEL-FG-ER split flange enclosure

for 90° feed-in of cables with connectors / IP65 The cable entry frames KEL-FG-ER are suited for installation of cables with connectors and conduits at an angle of 90° to the cabinet, enclosure or machine wall, providing an IP65 rating and strain relief for cable diameters from 1 to 16 mm (single-hole grommets KT 1 - 15) and 16 to 35 mm (single-hole grommets KT 16 - 34). The KEL-FG-ER-A frame matches exactly the cut-out dimensions for 24-pin standard industrial connectors. The KEL-FG-ER-B is suited for cut-outs 36 × 46 mm. The single-row versions KEL-FG-ER-E are particularly suited for flat connectors. The small frames are ideal for applications with limited space. Due to the…

Continue ReadingKEL-FG-ER split flange enclosure

Cable entry frames and cable grommets for flat cables

KEL-FL split cable entry frames for flat cables and prefabricated round cables / IP54 The KEL-FL range enables simple, fast and flexible cable routing and sealing of flat wires, e.g. in lift construction. Innovative construction of the grommets compensates for manufacturing inconsistencies in flat cables. Split KT grommets can be utilised to additionally route round cables with connectors. A flat rubber gasket is included in the shipment. Specifications IP rating (EN 60529): IP54UL Type (UL 50E): UL Type 12Material: PolyamideFlame class: UL94-V0, self-extinguishingOperating temperature: -40 C° to 140 C°Properties: vibration proof, UV-resistant, silicone free, halogen freeMounting options: Screw type mountingMounting height: 17 mm Advantages & benefits Routing of flat cables in combination with…

Continue ReadingCable entry frames and cable grommets for flat cables

KEL-FA split multi cable entry frames

for cables with connectors, tool-free assembly / IP54 The KEL-FA range is a compact system to route and seal pre-terminated cables as well as conduits or pneumatic hoses utilising KT series grommets. After populating the entry frame with grommets and cables, the cover is put on and the two clamping levers are locked with the lower part by pressing them down. The twist-proof construction of the KEL-FA enables intuitive assembly. Routing and sealing with IP54 for cable diameters from 1 to 35 mm. The KEL-FA frames match exactly the cut-out dimensions for 10-, 16- and 24-pin standard industrial connectors. These KEL-FA frames can either be screw mounted or simply snapped into the KEL-SNAP frame. Specifications IP rating (EN 60529):…

Continue ReadingKEL-FA split multi cable entry frames

Multi-membrane cable entry plates for cables without connectors

KEL-DPZ multi-membrane cable entry plates, round, with metric threads M25 - M63 / IP66 / IP68 / UL Type 12/4X* KEL-DPZ round cable entry plates are designed to route and seal cables without connectors or fibre optics (from 1.5 mm to 22 mm in diameter) in limited space. The assembly of the KEL-DPZ round with cables or pneumatic hoses can be done quick and easy. Simply make a small hole in the thin membrane, push the cables through. The KEL-DPZ round provides strain relief and protection IP66 / IP68 / UL Type 4X*. The round versions of the KEL-DPZ series have a thread to fit in metric cut-outs from M25 to M63. Thus…

Continue ReadingMulti-membrane cable entry plates for cables without connectors

Cable pass-through with brush seal

icotek offers cable pass-through solutions with brush seal like brush plates and brush strips that are perfectly suitable for applications where no high sealing rate is required. The icotek brush seal solutions are meant for dust and dirt-proof cable pass-through of lines with or without preassembled connectors. All brush cable pass-through products KEL-BES-S split brush plate for cable pass-through Split brush plates KEL-BES-S for routing cables into server racks, control panels and electrical enclosures. KEL-BES-S is also an ideal solution for entry and exit of cables that are routed inside raised floors, e.g. in computer centres. The brush plates can either be mounted via screws or via expanding rivets. Due to the split…

Continue ReadingCable pass-through with brush seal
Read more about the article KVT-W90 split 90° cable gland
KVT-W90 - icotek - Varga Elektronik d.o.o.

KVT-W90 split 90° cable gland

for cables with connectors, M32/M50 / IP54 The split KVT-W90 cable glands are used to insert and seal pre-terminated cables at a 90° angle. But also electric, pneumatic or hydraulic lines without terminals or connectors as well as corrugated conduits can be easily routed (e.g. into control panels, enclosures or machinery) and sealed with IP54. In particular, the KVT 50-W90 is perfectly suited to hold corrugated or smooth hoses. A large number of cable entry grommets is available to the user. By using multi-hole grommets up to 16 lines can be routed with one cable gland. Polyamide standard locknuts as well as a sealing ring are included in the shipment. Split locknuts can…

Continue ReadingKVT-W90 split 90° cable gland

icotek Service boxes

KT ServiceBox Part No.: 88001 Cable grommets, small: 110× KT for cables 1 - 17 mm10× BTK blank grommets10× KTMB multi - range grommets2× KT - DPF mutli - range grommets8× KT - ASI for ASI - Bus cables Cable grommets, large: 25× KT for cables 16 - 35 mm4× Blank / adapter grommets  3× KTMB multi - range grommets2× DT multi - membrane grommets   2× KT - DPF multi - range grommets Accessories: 2× KEL - U 10 cable entry frames1× KVT split cable gland  1× KZL strain relief plate1× Cable template QT ServiceBox Part No.: 88005 Cable grommets: 210× QT for cables 1 - 15 mm10× QTB blank grommets Accessories: 5×…

Continue Readingicotek Service boxes

CONFiX™ FWS bulkhead fittings for cable protection conduits

suitable for conduit screw connections or direct conduit pickup / IP54 The 90° angled conduit fitting CONFiX™ FWS is for installation of parallel corrugated cable protection conduits, e.g. in machines, control panels or control cabinets. The liftable cover is tightly fixed by a hinge. Therefore, the system is fast and easy to install. CONFiX™ FWS is offered in the following versions: CONFiX™ FWS-A with metric internal thread M16 to M50CONFiX™ FWS-B with a grooved conduit clip for types with sizes NW 13, 17, 23, 29, 37 and 50 The available colours are grey (RAL 7011) and black (RAL 9001). Specifications IP rating (EN 60529): IP54Material:: PolycarbonateFlame class: UL94-V0, self-extinguishingOperating temperature: -30 C° to…

Continue ReadingCONFiX™ FWS bulkhead fittings for cable protection conduits

KEL-DPU-HD hygienic multi-membrane cable entry plates

The new cable entry plates KEL-DPU-HD have been specially developed for installation in food processing and packaging machines. During the development according to the Hygienic Design guidelines, care was taken to ensure that the visible side of the cable entry plate are free of dirt-collecting recesses. The surface was kept very smooth (Ra = 0,421 μm acc. to ISO 4287). The outer contour has a radius of 6 mm instead of the required 3 mm. In addition, the KEL-DPU-HD uses an FDA-compliant elastomer in accordance with food approval 1935/2004/EG and (EU) 10/2011. The signal colour blue ensures a clear visual colour recognition.  KEL-DPU-HD entry plates are designed to route and seal cables without connectors…

Continue ReadingKEL-DPU-HD hygienic multi-membrane cable entry plates

IMAS-CONNECT™

Adapter grommets for Keystone jacks, PushPull connectivity and circular connectors By utilising the modular adapter system, the cable entry frame becomes a hybrid system. Pre-terminated and standard cables or hoses can be routed and at the same time the system serves as an interface for connectors.The new modular adapter system IMAS-CONNECT™ is a modular designed grommet system for mounting circular connectors, Keystone jacks, hose fittings, pressure compensation elements and much more.The grommets, made of elastomer with a polyamide body, fit perfectly into the split icotek cable entry frames, like KEL-U, KEL-ER, KEL-FG and KEL-QUICK and meet the protection classes IP54 to IP65 / IP66, depending on the grommet type. Order your free sample!…

Continue ReadingIMAS-CONNECT™

Strain relief acc. to EN 62444 for a secure cable management

ZL strain relief plates The strain relief plate ZL is used for static or dynamic applications for organising and securing cables on machines, control panels or drag chains. The design of the strain relief unit provides secure strain relief according to EN 62444. Mount of the cables or pneumatic tubing is easily done using cable ties. By using aluminium (ZL-AB types) or brass (ZL-MS types) nuts for the screw holes, a better fit of the strain relief plate is achieved, even in high vibration environments. Strain relief plates ZL 03 | 04 | 05 feature different comb widths. Thus providing a multi-purpose product for various cable sizes. For multilayer installation please use DH…

Continue ReadingStrain relief acc. to EN 62444 for a secure cable management

CONFiX™ cable conduit system

CONFiX™ FWS bulkhead fittings - for cable protection conduits Suitable for conduit screw connections or direct conduit pickup / IP54 The 90° angled conduit fitting CONFiX™ FWS is for installation of parallel corrugated cable protection conduits, e.g. in machines, control panels or control cabinets. The liftable cover is tightly fixed by a hinge. Therefore, the system is fast and easy to install. The available colours are grey (RAL 7011) and black (RAL 9001). CONFiX™ FWS is offered in the following versions: CONFiX™ FWS-A with metric internal thread M16 to M50CONFiX™ FWS-B with a grooved conduit clip for types with sizes NW 13, 17, 23, 29, 37 and 50 Specifications IP rating (EN 60529):…

Continue ReadingCONFiX™ cable conduit system

Cable management & EMC cable shield earthing for control panels, enclosures and cabinets

Control panel construction is required in numerous areas: Building technology, electrical engineering, industrial automation, power distribution, network technology, telecommunications... In these areas, electrical engineers are confronted with deadlines and cost pressure. High demands are placed on individual control panel solutions, short production time and high quality at low costs. icotek offers highly efficient and cost-effective solutions for every control panel application in the fields of cable feed-through, cable management and EMC cable shielding. Split cable entry systems and cable glands by icotek enable a fast, safe and cost-effective way to feed several preassembled cables (e.g. circular M connectors, Profibus, D-Sub, multi-pin power plugs...) through control panel, cabinet or enclosure walls, bases or roofs without…

Continue ReadingCable management & EMC cable shield earthing for control panels, enclosures and cabinets

KDR-ESR gland plates with slide frames

for Rittal, nVent Hoffman & Häwa enclosures / IP54 The KDR-ESR is a one-piece plate to be assembled on enclosure bases. Slide frames for the KEL-U cable entry frames are already pre-assembled. On some gland plate types KEL-JUMBO cable entry frames can be mounted as well. After installing all cables into the KEL-U frames, they are easily and quickly inserted into the slide frames and fixed. During maintenance, the KEL-U frames are removed without tools from the slide frames. Due to the combination KDR-ESR and KEL-U cable entry frames, a rating of IP54 is achieved (with correct selection of cable grommets). Slide frames which are no longer required, are closed with BPK-SNAP blank…

Continue ReadingKDR-ESR gland plates with slide frames

EMC shield clamps on earthing tapes

with or without integrated cable fixing function The earthing tapes are fitted with a shield clamp at one end. This solution is used where space is limited. The earthing tapes are available with M4 or M6 holes. Specifications Material: Shield clamp: Spring steel, zinc plated / Base frame: Cu-ETPProperties: vibration proofMounting options: Screw type mounting,Riveting Advantages & benefits Very flexible assemblyInstallation even in places that are difficult to accessEarthing tapes with pressed-on connecting end padsStandard products, short delivery times UL listed Order your free sample! Download PDF MB|MSKLMB|Z-MSKL Product nameNo. of shield clampsFor max. no. of cablesHole sizeCross-sectionCurrent loadLength x Width x HeightPUPart No.MB|100|6|M4|MSKL 3-1211M46 mm²67 - 80 A113 x 14,9 x 25 mm10…

Continue ReadingEMC shield clamps on earthing tapes

KEL-DPF pyramid cable entry grommets

for single cables with diameters up to 70 mm, M25 - M85 / IP66 / IP68 / UL Type 12/4X The KEL-DPF was developed particularly for routing large or unknown sizes of cables into a switch cabinet or machine (max. cable diameter 70 mm). Due to the flexibility and unique pyramid shape, cable entry and flexible positioning is much easier compared to using conventional cable glands. Also perfect for bundling or restraining large cables. Cutting of DPF grommets: Cable diameter less 25%. The corresponding diameters are marked on the grommet. It is recommended that additional strain relief be provided for cables using cable ties. For mounting the KEL-DPF sizes 75 and 85 we…

Continue ReadingKEL-DPF pyramid cable entry grommets